Dillon 30423-0014 X-C Mechanical Force Gauge Compression Calibration without Maximum Hand - 10,000lb Capacity
Similar Products to Consider
Available in capacities from 50 lb to 25,000 lb or 50 kg to 10,000 kg
1% accuracy of full range
The Dillon X-C Mechanical Force Gauge with Hardened Ball is available in nine capacities from 50 lb to 25,000 lb or 50 kg to 10,000 kg. Accuracy is 1% of full range.
Load is applied against a hardened ball which rotates to maintain vertical alignment as pressure increases. The ball is held in place with a spring clip or retainer. A threaded mounting hole is located opposite the loading ball in the bottom of the beam.
Proven accuracy and ruggedness sets our Dillon X-C Mechanical Force Gauge with Hardened Ball apart in the force measurement industry. The "D" shaped deflection beam is the heart of the X-C.Highly engineered materials with close machining tolerances and proper heat treatment provide optimum strength and spring characteristics.
Calibration is available in pounds or kilograms.
Specifications
| Warranty | 2 Years |
| Accuracy | 1% Model 30449-0014:2% |
| Operating Temperature | up to 120F (48C) |
| Overload rating | Accidental overloads up to 30% of capacity can be safely sustained without injury to the dial indicator or deflection beam. All capacities feature a 5:1 design safety factor. |
Ranges
| Model | Capacity | Resolution |
| 30386-0035 | 50 lb | 0.5 lb |
| 30386-0043 | 100 lb | 1 lb |
| 30446-0033 | 250 lb | 2.5 lb |
| 30446-0017 | 500 lb | 5 lb |
| 30444-0019 | 1,000 lb | 10 lb |
| 30388-0017 | 2,000 lb | 20 lb |
| 30389-0016 | 5,000 lb | 50 lb |
| 30423-0014 | 10,000 lb | 100 lb |
| 30449-0014 | 25,000 lb | 250 lb |
Low Beam Deflection
| Capacity | Deflection | Capacity | Deflection | |
| 50 - 250 lb (25 - 100 kg) | 0.019" | 2,000 lb (1,000 kg) | 0.011" | |
| 500 lb (200 kg) | 0.016" | 5 and 10,000 lb (2 and 5,000 kg) | 0.010" | |
| 1,000 lb (500 kg) | 0.018" | 25,000 b (10,000 kg) | 0.022" |
Display Callout
| 1. | Deflection beam | 8. | Anvil set screw |  | |
| 2. | Dial indicator with zero at standard 12:00 position | 9. | Mounting bracket for dial indicator | ||
| 3. | Bezel | 10. | Screws for mounting bracket | ||
| 4. | Maximum load pointer (optional) | 11. | Bezel-locking screw | ||
| 5. | Pressure button | 12. | Loading ball | ||
| 6. | Slanted Anvil | 13. | Spring retainer clip | ||
| 7. | Dial indicator plunger |
Principle of Operation
A D-shaped deflection beam is the heart of the Dillon Force Gauge. Machined to close tolerances, beams are heat treated to develop optimum strength and spring characteristics. High-strength aluminum is used in Model X instruments through 500 lb (200 kg). Ranges above this are fabricated from aircraft-quality alloy steel.
A precision dial indicator is mounted at the null point of the deflection beam. The indicator plunger rests against a slanted anvil at the open end of the beam, as shown in the photo. Under compression loads, the two halves of the beam tend to close. Tension force causes them to move apart. This action pushes the plunger inward, as determined by the slant of the anvil. Readings produced on the dial are in direct relation to applied load.The pointer revolves 360 clockwise under compression or tension forces. Push-pull gauges read half scale (180) clockwise in compression, and counterclockwise, 180 from center zero under tension loads.
Options
- Shockless dial indicator for installations involving the sudden application or release of force. (Maximum pointer cannot be supplied with shockless dial indicator)
- Maximum load pointer which remains at peak load until manually reset.
- Zero position on dial may be factory positioned at 12, 3, 6, or 9 o'clock. Standard position is at 12 o'clock.
Downloads
 | DillonX-C Mechanical Force Guage with Hardened Ball - Data Sheet |
| DillonX-C Mechanical Force Guage with Hardened Ball - Instruction Manual |
